Project Preliminary Fail

I bought some 12V LED filament bulbs for a preliminary delve into a project I'm thinking about building... Only...

That ain't no filament.

Ship Diorama Build Blog : HMS Rodney : Pt6

I've been looking at some reference material and I'm going to try to get close to, but I'm not obsessing over getting the same paint job... So here it is, lost of masking first off and then a solid colour, the numbers I give are all Revell Aqua Colour, and to remind you I'm brush painting.

From the stern, light Grey 73.  And you can see flexible tamiya masking tape to keep the rim of the hull coloured, but protect the deck itself.

I also used some humbrol maskol to keep the line perfect.

I put the dark gret and light blue 49, along with white 05 highlights.

And started to mask the areas for the darker shade, for which I selected Tar Black 08.

Peeling all the masking I'm getting slightly better I think, I've had very little bleed under, despite thinning the paint to keep the brush strokes from showing too much.

The reference I have is mainly long strokes, but at the bow there are these three rounded shapes in white, with inner grey circlets.

I started some of the deck details, marching the alignment of the hull shapes.

And finally, some gratuitous shots mounted on the base.

Ship Diorama Build Blog : HMS Rodney : Pt2

This base build is very time consuming, mainly due to the requirement to allow layers to dry and set before proceeding onto the next layer.  As such when I move onto the two other models I'm going to make both ships at the same time, this is so that I'm using the same materials at multiple times across the pair.

As mentioned before the first colour layer was put down and covered, I have since repeated this, layering the tissue paper and 50:50 PVA to water mix and softening or adding wavelets as I've gone.

As this dried you can see the previous colour layer coming through quite strongly.  But before more colour could go on it needed now to dry completely.

So, I set about mounting the black plastic hull base from the model itself.

First a test fitting into the wave front for the bow...

 Then I spent time cleaning up the base to allow the line of the hull to sit into the sweeping water feel now built up...And once I was happy I drilled two holes in this base...

Through them I then pushed a cocktail stick...

Cutting it neatly and then adding a dot of superglue to fix them in place, these are now through the plastic and into the polystyrene, but they're not permanent, the base can be pulled off, it's only held by a little excess PVA and the sticks.

Adding the weight, stuck down with a liberal swish of superglue completes this preparation...

And a hull test fit confirms things are going to work out....

Next, with thinner I took aquamarine and blue/green acrylic paints and gave a nice but randomly shaded 

At this point the base has been left to dry for 24 hours.

I plan to pick out the wave crests with some white and add a little more detail to the wake, but the base colour, wave shape and layers of modelling are done.

We'll return to the base only for the edges needing colour and building our frame and badge.

On to some actual model painting!

See the other parts here:

Part 1

Part 3

Part 4

Ship Diorama Build Blog : HMS Rodney : Pt1

The eagle eyed of you will have seen the slew of short model videos going onto my YouTube Channel, and the great and good among you will have subscribed there already, if not the YouTube link is always right there in my blog.

But my new project is a blog exclusive, I'm not planning on filming much of this build, instead we're going to use more high-resolution photographs taken on my phone.

It's also going to be one of the biggest "things" I've ever built.  I've returned to modelling as a hobby in my middle age, but as a kid I was very keen model maker and I had literally hundreds of planes in zoom poses hung from my bedroom ceiling.

But I also had a small fleet, I had the HMS Belfast, HMS Hood and HMS Illustrious in 1/600 by Airfix on my window sill.

In fact in my mid 20's I actually bought and build a second HMS Belfast, which I actually left in my then rented house when I moved out, as I could not find anywhere to put it, but couldn't bring myself to throw her away.

Anyway, I've now decided to start a new fleet and I've decided to go with a 1/700 build of one of my favourite ships HMS Rodney.  Historically this lends some symmetry to my old HMS Hood, as the Rodney exacted terrible revenge by helping to sink the Bismark.

This smaller scale is perhaps my challenge, and the level of detail I want to bring to the model is going to likewise be a challenge.  And I am on the hunt for more detail sets and photo etch to put into use before I get started.  As such, I need to start the model somewhere other then itself, and I've decided on making a diorama.

I can't possibly use epoxy, it's too cold to go work outside and working in my office, I have to be able to put my model making kit all away, so a long cure time is out of the question.  I'm therefore going to start small and simple... I can after all lift the ship back off this base at anytime.

The first step was to use the included base as a template, I tried on card, but immediately saw the materials I had at hand would cause it to disintegrate.  So I found this piece of 2 inch thick polystyrene from a package, and started to mark out the outline.

Next I cut the large sheet to roughly the right size and broke off the excess material.

Next I needed to do some preparation work, I decanted some of my PVA into a spare jar, which has a lid, putting in about 60g of the glue and 80ml of water I shook them vigorously until I had a quite runny PVA mix.

I also retrieved a single piece of aluminium foil roughly the size of the whole base, and I started to roughly layout and gently manipulating the foil to fit like the first layer of my wave effect.

Once I was happy I slipped these aside and painted a layer of neat PVA quite thickly onto the base and then started to place the foil back in place.

making sure to let the foil fall as it liked.

Once it was completely covered I then took single sheets of toilet paper and the PVA water mix and started to layer them over the foil, with the aim of softening the harsh lines, but keeping the pattern random and natural.

Once complete I did a test fit of the plastic base.

And from that alignment started to layout very thin lines of paper and foil atop the current layers, to make an inflection of a bow wave.

A quick test fit.

And once I was happy I got the acrylic paints out, very dilute with water I started with a deep aquamarine gloss from Revell.  Adding a hint of green gave this strong bold colour a real flare of effect.

But, this is only a hint layer and so another layer of toilet paper, single ply this time, was used with the watered down PVA to activate the paint and bring it through.

This further softened the overall wave effect, this is notcable most in the left of field and in the bow wave being much softer and appearing to roll.

A final smattering of watered PVA and I set this whole thing aside.

My plan going forward is to let it dry completely, then trim the excess foil and paper from around the edges, before hitting the glossy acrylic again, but that will be softed with white/grey.  And I'll gloss varnish after that, before picking out the waves with white and giving everything a second gloss varnish.

I've seen a recommendation to use a high gloss varnish of another type, so we'll see... either way, for my first base ever, I'm happy so far, and... it's kept me out of trouble for two and a half hours making it.

See the other parts here:

Part 2

Part 3

Part 4