Ship Diorama Build Blog : HMS Rodney : Pt15

So, I'm literally scared of rigging... It scares me.  I therefore try to keep my technique simple, a single pair of sharp scissors, a single metal tweezer, my hands and superglue.

I then let out a pool of superglue and let it cure a little whilst I unfurl a length of rigging elastic, I'm using mig's here.

Then I use a cocktail stick to put a dot of partially cured glue at the start and end points... The start I then let the rigging rest in the dot of glue and hold with my left hand and then my dominant right hand can move the rigging into place and let it sit at the right tension (or slack) in the end dot of glue.

If I use fresh glue it simply takes too long to cure, partially cured already going and it's just right, but you can end up with thick layer upon layer of it, specially when doing multiple runs - we will look at the stern of my ship in part 16 maybe....

However, for now here are some pictures of the rigging to the signal deck and bridge wing struts.

Ship Diorama Build Blog : HMS Rodney : Pt14

The penultimate post!  Yes we're nearly there with the actual paint and build, we have two pieces to give us the planform of the ship the small pieces are the anchors...

The larger piece is the main mast... which was a bit of a pest.

To get it straight under it's own weight with a single point of glue.

I went with a dot of superglue, which I had led oxidize and cure a touch.

This let it at least sit whilst I then held it with a single finger, whilst it solidified a little more.  And then finally I put a layer of extra fresh superglue with a cocktail stick on the crows nest to just hold it level.

The final touches were then to a little deck furniture.

Next, and this truly scares me, is the final pieces of rigging...

We will get to that in due time.

Ship Diorama Build Blog : HMS Rodney : Pt13

Well, it's been eleven months since I started her, and now it's been nearly eight since I last touched her, but finally, after a tumultuous period I'm back at the model making bench... Working on finishing the Rodney, the first task was to remove the dust which had gathered.  Then to start to fit the out rigger boats.

I took the ship off the weighted base, and the turrets off to dust her.

The waves were the worst thing to dust.

I spotted this section of the deck, behind the middle turret mount needs painting.

The first starboard side boat, the cleats added with poly cement and left to set, then the boat gun with super glue.

Close up of the port-side boats through my new magnifying boom.

And a general look at my work bench.

Highlights are the use of my new magnifying lighting boom... lovely.

Ship Diorama Build Blog : HMS Rodney : Pt10

 Today, before I get working I thought I'd sort out the things on my desk... of course with working from home my work space is pulling double duty, but here it is.... 

Yes, that is a coffee and a pint of juice, this is hopefully going to be a nice long uninterrupted modelling session.

First things first, lets review the other three secondary battery casements and get them superglued and we can plan out the rest of the boat deck too....

I do this supergluing by actually decanting the glue onto another surface, the best I've found is the plastic coated card on pakaging, here I'm using an old packet of tablets wrapper, decant and I can dot the glue around with a cocktail stick and touch things.

I use cocktail sticks and bluetac to hold parts for painting...

So they're the three starboard side secondary battery, I give them and the others a first coat after test fitting, they all get the sky blue colour first.

I also give the two unpainted main turrets a coat of grey, then skyblue highlights

Before masking them and adding flash details in darker tones and painting the rooves.

My references here are a little hazy, so I've used artistic license.... She's my ship now.

Ship Diorama Build Blog : HMS Rodney : Pt5

 Today I've decided to work on the decks, now I was using Revel Ocre 88 as my base, this is just a flat colour, no shading, no detail nor weathering; that'll all come later.   But my initial coat was very fine, but just not covering the plastic.  So three layers later the colour is better and more consistent, but it has now pretty much wiped what little intimation of planking there was in the plastic surface.

I has also created myself a problem.  My plan is to paint and detail the deck then mask it before doing the hull sides, and because I hadn't masked it there was now paint on the hull, that needs cleaning off.

Once I was happy I decided to have a play at some detail.  Mixing a little leather brown into the ocre and thinning it, then cutting some stencils with plank like shapes....

I started to put little plank marks, the odd replaced deck plank.

I didn't do too many of these, I will perhaps do more and I'm going to take a look at what happens to a deck after being salt scoured and washed down by mops for a long time and add something like that to break up the field of ocker I currently have.

My next step however was to start preparing for the colourful hull camouflage, and this time I needed to mask around the rim of the deck, to break the steel hull from the wooden deck...

For this I used flexible masking tape to pick out the edge and on the right you can see a vertical tape line, this demarcates the furthest extent of a certain colour I'm going to use on that rear quarter, so the tape tells me I'm safe to paint that first colour to that line.

I also masked out some of the eye catching sea spray shields on the forecastle.

My final step was to pick out a little detail on the stern and look at the two AA guns I need to build there.  I was hoping to build to the 1942 look, but the AA guns as I have them appear to be the single barrel 20mm style, rather than the quad barrel pom-poms fitted later.

I don't have any photo etch, so I may look t building a pair of 4 barrel pom-pom looking parts from scratch.  However, I need to make shields for the gun emplacements... that'll be a challenge.

This is my reference for this....

Ship Diorama Build Blog : HMS Rodney : Pt4

Tonight I've spent a fruitful two hours completing some details, clean up and fitting then I've actually taken a brush to the model...

The first piece was adding some wire cut and bent, then super glued into position, to represent the two wing bars, I'm not even sure what these things are, they're serviced from the gun deck by ladders, which are molded into the plastic.  In real life they were suspended by a double back rope pulley, but I can't possibly model that, so I'm just giving the intimation of them.

They were held in place with a piece of masking tape, super glued and then cropped to length.  Bending was performed with a pair of pliers, but I could not for the life of me get them straight.

The next problem was fitting the roof on the bridge, and in the image above you can see the two proud forward prongs of plastic, these needed sanding down but the detail retaining.  Else the roof was sitting high out of place.

Much sanding and test fitting later and it looked about right.

Finally the rear of the bridge has a vertical slit gap that needed a touch of filler.

 And the same on the front.

And the roof was fitted.

Then, the whole thing had to dry a little before some 2000 grit sand paper was used to smooth the rear wall and take the seams off of the bridge module.

A glorious look at things on the base was then required...

And you can see the leading markers from the bridge top... and guess what came in the mail today...

Yes, I am going to add rigging.

Brush time... I can't resist painting, I paint with a brush, not an air brush, so I thinned some Revell Aqua Colour Ocker 361 (88) at about 70% paint to 30% Revell Acrylic thinner and put on a very fine layer on the decks.

The challenge here was to keep the details of the plastic, which does have a hint of deck planks.

Three coats on the forecastle and fore section of the gun deck (forward of the middle mount) and you can really see it coming together.

And I painted the aft section of the bridge and superstructure, which is clearly decked too.

You can clearly see the decking still on the super structure and how thin my paint layers are on the deck, here we see the near finished deck of the super structure (3 coats) and the main deck (1 coat).

See the other posts here:

Part 1

Part 2

Part 3